With regard to circuit simulation: have a look for LTSpice on the
Linear Technology website. Or if you don't mind text-based netlists
and classical Spice, see
http://www.rfglobalnet.com/IndustryS...hResults.aspx?
keyword=Spice&TabIndex=4&image1.x=0&image1.y=0 for some other sources.
With regards the circuit, it's fairly easy to do some mental arithmetic
to see if there is an advantage or not over the two-diode, two-caps,
floating-transformer "full wave voltage doubler" circuit.
In the old circuit, there are, if you will, four distinct time periods
in each cycle (though two of them are electrically equivalent, and the
other two are symmetrical). One is where the upper cap is charging,
and the load current may be considered to be through the two caps in
series -- or may be considered to be through the lower cap and the
transformer and upper diode. Following that is a period where the
transformer voltage is too low to charge the upper cap and too high
(not negative enough) to charge the lower cap. Then the load current
flows through the two caps in series. Following that, the transformer
charges the lower cap, and after that the transformer voltage is again
too low to forward bias either diode. So the net voltage across the
two caps increases twice each cycle, once when the upper cap is
charging and once when the lower cap is charging. The output (load)
ripple fundamental frequency is twice the line frequency. You can get
a reasonable idea of the ripple voltage if you assume the charging
takes place in a tiny fraction of the total cycle time; in fact, that
will be an upper bound on the ripple voltage. For simple analysis,
assume a 1Hz input so there are two charging pulses per second (one per
cap), and assume two 1-farad caps and a 1-amp load. Then the voltage
across each cap between the charging pulses sags at 1 volt per second,
and the output sags at 2 volts per second, but resets twice per second,
so the ripple is 1 volt peak to peak.
In the new circuit, you need to say something about the capacitor
values. Presumably the two "input" caps are the same value, but may
differ from the output cap. But what happens if you say that you are
going to use the same total energy-storage ability as you had in the
simpler circuit? Then the output cap might be, say, 0.25 farads, and
the two input caps might be 0.5 farads each, since the output cap must
be rated at twice the voltage of the caps in the original circuit.
Now...can you figure out an allocation of the caps that gives you even
the same performance as the original circuit, let alone a better one?
And is it worth using more caps and more diodes? Especially for low
voltage use, the original circuit has a distinct advantage of having
only one diode drop during charging.
You can also analyze transformer utilization and I think you'll find
that the "improved" circuit doesn't really offer any advantage, if you
set it up to give the same output ripple.
Any other viewpoints, backed by some analysis or simulation?
Cheers,
Tom
David J Windisch wrote:
Build s test ckt with a filament xfmr and *small* caps and a "heavy"
load,
and look at the oupt ripple with a scope. Or build it virtually.
OT: Which are the other good, (affordable!?) ckt sims?
Anyone have a transferable version of Electronics Workbench he'd like
to
sell?
73, Dave, N3HE
Cincinnati OH
"Mike Silva" wrote in message
ups.com...
Regarding the circuit he
http://www.kwarc.org/bulletin/99-04/tech_corner.htm
Does this voltage doubler work any "better" (better regulation,
better
transformer utilization, etc) than the classic 2-diode, 2-capacitor
doubler (as seen in e.g. the HP-23 supplies)? I know it uses more
parts; what I'm wondering is whether the extra parts actually
provide
any benefits, and if so, under what circumstances.
Does anybody have any actual experience with this circuit?
73,
Mike, KK6GM