"Pete KE9OA" wrote in message
...
Did you do the I.F mods that are on www.mods.dk ? I remember that this
Thanks for the response, Pete. Yes, very effective. BTW, I posted the mods
there.
Now, as far as filter switching diodes, my favorite (doesn't mean that
this is the best) is the 1N5767 PIN diode, biased at around 75mA. I have
had good results using leaded devices.
Is that still a good choice if I can push only 10-12mA? It would require a
complete redesign to go higher.
The RF preamp is a 3SK195 and the 1st mixer uses a pair of these balanced
for RF and driven in parallel by the LO. Is there any point in
paralleling a second 3SK195 (piggyback style) on the preamp? on the
mixer? Or changing out the transistor type? How would one determine/set
the correct operating point?
The radio doesn't seem bad in this respect. I haven't had one for several
years, so I wouldn't be able to give an intelligent answer without the
schematic. You could look at the Icom R75 schematic and see how they
implement their RF amp. I believe that they do use the configuration that
you suggest.
I really meant piggyback! No additional components but probably would have
to change out the resistors to set the operating point correctly. Wondered
if it was a crazy idea or had merit.
The 1st IF (45 MHz) filter is a 2-pole crystal filter with 15kHz bw
at -3dB, 100kHz at -24 dB. I acquired a 30kHz/-3dB, 120kHz/-40dB matched
pair that I was thinking of substituting in order to widen bandwidth for
DRM. Note that the centre of the 2nd IF tunes across a 5kHz segment of
the 1st IF passband so that a 10kHz or wider bw at the 2nd IF rolls off
on one side or the other because of the shoulders of the 15kHz 1st IF. Is
this a bad idea for intermod? The stopband attenuation is going to be
poorer out to maybe 50-60 kHz bw but should be better beyond that, apart
from stray coupling due to squeezing in a pair of filters where one would
ordinarily be.
What are your thoughts?
73, Tom
Tom, you should be able to use a wider bandwidth crystal filter. The
natural impedance of the filter would probably be different than the
current filter. If the impedance matching is not correct, you will have a
couple of problems.
First of all, the insertion loss and passband ripple can increase. If
group delay is important for DRM, this could be a problem. I don't know if
bit error rate is a consideration in this case.
Secondly, I would take a look at the 910kHz rejection of the filter that
you are considering. If it is not high enough, you will be able to hear
that (2 X 2nd I.F) response.
I am looking for a wider, flatter response around the uniform spectral
density of the common 10kHz DRM channel for better group delay but I'm not
sure that DRM is so very susceptible because there is pronounced and dynamic
group delay inherent in ionospheric propagation. A 1dB ripple is considered
ideal so I imagine that a flat amplitude-frequency and linear
phase-frequency response in the radio have a small beneficial effect on the
rate of successful decoding. There is also a 20kHz wide DRM mode.
The 4-pole cascaded filter is spec'd to have minimum attenuation of 70dB
at +/- 910kHz and 800ohms/1pF terminating impedance. The filter it replaces
is unspecified at +/-910kHz but I would guess that it is 35-40 dB; its term
impedance is 560/6 ohms/pF. So the 910kHz image suppression should be
improved by up to 35 dB less strays. Filter loss will increase by 1.5 dB per
spec. If the circuit currently matches the stock filter, is the ripple and
increased loss liable to be severe?
73, Tom