|
Tektronix 7603 scope behavior when readout board is missing
Greetings:
I just acquired a Tek 7603 scope with 7A18 dual-trace vert. and 7B53A timebase plugins but upon internal inspection and cleaning discovered that the readout board (when facing the front of the instrument it is found on the upper right side midway along the length) is missing, as are all interconnecting cables it uses. The display is very corrupted: odd blanking and sawtooth displays appear with no vertical input and horizontal sweep width changes with timebase selection in a drastic way. A vertical input signal modulates the strange displays in a fashion that suggests the vertical section is functional and the vertical position controls do work. The plugins are supposed to be in operating condition. The internal logic timeshares the display between readout and waveforms and is rather complex and implemented in Tek custom hybrid ICs and a mix of TTL and CMOS. I would really appreciate a report of the behavior on a working 7600 series scope when the readout board is disconnected; the service manual describes various voltage measurements with the board removed so it is permissible to do so and power the instrument (but no mention is made of the scope's behavior with the board removed). Many thanks to anyone willing to do this. Regards, Michael |
Tektronix 7603 scope behavior when readout board is missing
On Sat, 05 May 2007 22:14:57 -0500, msg wrote:
Greetings: I just acquired a Tek 7603 scope with 7A18 dual-trace vert. and 7B53A timebase plugins but upon internal inspection and cleaning discovered that the readout board (when facing the front of the instrument it is found on the upper right side midway along the length) is missing, as are all interconnecting cables it uses. The display is very corrupted: odd blanking and sawtooth displays appear with no vertical input and horizontal sweep width changes with timebase selection in a drastic way. A vertical input signal modulates the strange displays in a fashion that suggests the vertical section is functional and the vertical position controls do work. The plugins are supposed to be in operating condition. The internal logic timeshares the display between readout and waveforms and is rather complex and implemented in Tek custom hybrid ICs and a mix of TTL and CMOS. I would really appreciate a report of the behavior on a working 7600 series scope when the readout board is disconnected; the service manual describes various voltage measurements with the board removed so it is permissible to do so and power the instrument (but no mention is made of the scope's behavior with the board removed). Many thanks to anyone willing to do this. Regards, Michael Post what options were sold as part of this scope. Some were sold without readouts, the fact there are no connectors indicates that possibly the readout option was deleted. IMHO, (and this is just a WAG) the problem you are reporting is not related to the readout... |
Tektronix 7603 scope behavior when readout board is missing
PeterD wrote:
On Sat, 05 May 2007 22:14:57 -0500, msg wrote: snip I would really appreciate a report of the behavior on a working 7600 series scope when the readout board is disconnected; the service manual describes various voltage measurements with the board removed so it is permissible to do so and power the instrument (but no mention is made of the scope's behavior with the board removed). snip Post what options were sold as part of this scope. Some were sold without readouts, the fact there are no connectors indicates that possibly the readout option was deleted. Digging through Internet archives this morning I noticed a few posts from folks seeking the readout board for 760x scopes with a mention that 'Option 01' was a cost-reduced version sans this board so evidently the scope should work without it (if properly optioned?). I was not sure if any cable modifications would be needed if the board were removed from a scope not-so-optioned. And indeed I now discover an "Option 1" label on the bottom of the left bay so this scope never had the board. Its problems are elsewhere. Thanks, Michael |
Tektronix 7603 scope behavior when readout board is missing
msg wrote:
Greetings: I just acquired a Tek 7603 scope with 7A18 dual-trace vert. and 7B53A timebase plugins... snip The display is very corrupted: odd blanking and sawtooth displays appear with no vertical input and horizontal sweep width changes with timebase selection in a drastic way. A vertical input signal modulates the strange displays in a fashion that suggests the vertical section is functional and the vertical position controls do work. The problem was a defective C811 (14000 uf / 25v), the -18V filter capacitor for the -15V supply. Scope works well now. Regards, Michael |
Tektronix 7603 scope behavior when readout board is missing
On 7 Mai, 04:12, msg wrote:
msg wrote: Greetings: I just acquired a Tek 7603 scope with 7A18 dual-trace vert. and 7B53A timebase plugins... snip The display is very corrupted: odd blanking and sawtooth displays appear with no vertical input and horizontal sweep width changes with timebase selection in a drastic way. A vertical input signal modulates the strange displays in a fashion that suggests the vertical section is functional and the vertical position controls do work. The problem was a defective C811 (14000 uf / 25v), the -18V filter capacitor for the -15V supply. Scope works well now. Regards, Michael Sounds good to my repair eperience. Due to own experience bad/dried filter caps in the LV pwr supply of Tek 76xx is often a problem. I had more than 50 of these for repair, and most of these due to cap problems. Good luck with your fresh repaired scope, it is a nice instrument (with and without readout option). hth, Andreas |
| All times are GMT +1. The time now is 08:27 AM. |
Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
RadioBanter.com