Home |
Search |
Today's Posts |
#11
![]() |
|||
|
|||
![]()
A quick note Power Poles and mobile operation.
Use the smallest cable tie to hold the two connectors together as they sometimes have a tendency to shake / pull apart. Bill - WB1GOT On Tue, 18 Dec 2007 10:09:13 EST, KC4UAI wrote: It's not been an issue for me until this Christmas when my wife decided to get me a VHF/UHF mobile rig. I've been using an older Icom 2 meter rig in both the cars for years so both cars have Icom power cables in place, but the new rig doesn't use the same power connectors. I'd like to settle on a common power connector for both the radios, but I'm not all that sure where to go to find something that is reasonably priced and is not going to disappear in the future and force me to go out and buy all new connectors again. I figured I'd not remove any of the existing connectors on the radios, but build up short jumpers that adapt to the connector of choice. I also figured that I'd use the existing power wires by replacing the current Icom power connector with what ever I pick. Any suggestions on what to use and where to get them? -= bob =- |
#12
![]() |
|||
|
|||
![]() "Dave Platt" wrote in message ... One source is http://www.powerwerx.com I pretty much always get them at hamfests, but I often end up getting them from Tower Electronics, who has an online presence. http://www.pl-259.com/page4.html Looks like they are more expensive than PowerX tho. About the same for the plug but double for the socket. ... |
#13
![]() |
|||
|
|||
![]() "Bill Powell" wrote in message ... A quick note Power Poles and mobile operation. Use the smallest cable tie to hold the two connectors together as they sometimes have a tendency to shake / pull apart. They have little clips you can get to prevent them pulling apart. ... |
#14
![]() |
|||
|
|||
![]()
In article ,
xpyttl wrote: Icom VHF radios now all use the same T connector, and I believe almost all other major manufacturers have moved to that connector for VHF/UHF radios. Kenwood also. Does anyone know where I can get a supply of these "T" connectors, both the male & female ends? I have found the female connectors with 6' of heavy wire and fuse holders for about USD20, which I see as a bit pricey, but not the male ends (the end that is on the radio). -- Rich Greenberg N Ft Myers, FL, USA richgr atsign panix.com + 1 239 543 1353 Eastern time. N6LRT I speak for myself & my dogs only. VM'er since CP-67 Canines:Val, Red, Shasta & Casey (RIP), Red & Zero, Siberians Owner:Chinook-L Retired at the beach Asst Owner:Sibernet-L |
#15
![]() |
|||
|
|||
![]()
In article ,
Rich Greenberg wrote: Kenwood also. Does anyone know where I can get a supply of these "T" connectors, both the male & female ends? http://www.powerwerx.com Click "Connectors" on the left, then "OEM Connectors". The OEM "T" male and female connectors are $1.95 per connector (one shell and two inserts). -- Dave Platt AE6EO Friends of Jade Warrior home page: http://www.radagast.org/jade-warrior I do _not_ wish to receive unsolicited commercial email, and I will boycott any company which has the gall to send me such ads! |
#16
![]() |
|||
|
|||
![]()
On Wed, 19 Dec 2007 20:55:37 -0500, Rich Greenberg wrote:
Does anyone know where I can get a supply of these "T" connectors, both the male & female ends? I've bought them from Tower Electronics, http://www.pl-259.com/ . I'm sure there are a number of other vendors online. |
#17
![]() |
|||
|
|||
![]()
I suggest Powerpole connectors, since they are becoming quite
popular among hams active with RACES and ARES. One source is http://www.powerwerx.com/ (the 15/30/45 ampere model; the shells are all the same and the metal insert is chosen based on wire size). Note that the crimp connector from Anderson is expensive. Powerwerx suggests a GB crip tool, which I have. It tends to make the metal pieces a bit too wide, so you have to squeeze them with pliers to make them fit into the shell. You might want to solder them, if you're good at that. 73 de WY2Y "KC4UAI" wrote in message ... It's not been an issue for me until this Christmas when my wife decided to get me a VHF/UHF mobile rig. I've been using an older Icom 2 meter rig in both the cars for years so both cars have Icom power cables in place, but the new rig doesn't use the same power connectors. I'd like to settle on a common power connector for both the radios, but I'm not all that sure where to go to find something that is reasonably priced and is not going to disappear in the future and force me to go out and buy all new connectors again. I figured I'd not remove any of the existing connectors on the radios, but build up short jumpers that adapt to the connector of choice. I also figured that I'd use the existing power wires by replacing the current Icom power connector with what ever I pick. Any suggestions on what to use and where to get them? -= bob =- |
#18
![]() |
|||
|
|||
![]()
On Sat, 22 Dec 2007 18:18:30 EST, "Geber"
wrote: Note that the crimp connector from Anderson is expensive. Powerwerx suggests a GB crip tool, which I have. It tends to make the metal pieces a bit too wide, so you have to squeeze them with pliers to make them fit into the shell. You might want to solder them, if you're good at that. You might want to use the correct tool - the West Mountain ratchet crimper. I invested in one of those several years ago and consider it one of my best tool investments in all the years. -- 73 de K2ASP - Phil Kane From a Clearing in the Silicon Forest Beaverton (Washington County) Oregon e-mail: k2asp [at] arrl [dot] net |
#19
![]() |
|||
|
|||
![]()
In article ,
Phil Kane wrote: Note that the crimp connector from Anderson is expensive. Powerwerx suggests a GB crip tool, which I have. It tends to make the metal pieces a bit too wide, so you have to squeeze them with pliers to make them fit into the shell. You might want to solder them, if you're good at that. You might want to use the correct tool - the West Mountain ratchet crimper. I invested in one of those several years ago and consider it one of my best tool investments in all the years. Do you know whether the die (anvil-and-punch) sets for the PowerPole connectors are available separately? There are several brands of ratchet crimper handles which take interchangeable die sets (Ideal and Paladin among others). I've got one such, and I'd rather spend $25 or so on a die set to add to my collection rather than buying a whole new set of handles. -- Dave Platt AE6EO Friends of Jade Warrior home page: http://www.radagast.org/jade-warrior I do _not_ wish to receive unsolicited commercial email, and I will boycott any company which has the gall to send me such ads! |
#20
![]() |
|||
|
|||
![]()
On Sun, 23 Dec 2007 19:08:28 -0500, Dave Platt wrote:
Do you know whether the die (anvil-and-punch) sets for the PowerPole connectors are available separately? There are several brands of ratchet crimper handles which take interchangeable die sets (Ideal and Paladin among others). I've got one such, and I'd rather spend $25 or so on a die set to add to my collection rather than buying a whole new set of handles. The dies are removable on the West Mountain crimper (I just checked), but it is a different style handle than the RF Industries Handle I have at work. I didn't try to see if they would interchange and I don't know if WMR would sell the dies seperately. I recall paying about $50 for the WMR crimper from Powerwerx. The WMR crimper gives a perfect crimp so long as the handles aren't squeezed beyond the point where the ratchet releases. 73, de Nate -- "The optimist proclaims that we live in the best of all possible worlds, the pessimist fears this is true." |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Forum | |||
WTB: TR-4 xcvr power connector | Boatanchors | |||
TCS power connector | Boatanchors | |||
WTB: Power connector for BC 260 | Swap | |||
FA: New BC-348 Power Connector | Boatanchors | |||
FRG-100 What power connector ? | Homebrew |