Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Old August 6th 07, 08:19 AM posted to rec.radio.amateur.antenna
external usenet poster
 
First recorded activity by RadioBanter: Jul 2007
Posts: 8
Default non-antenna question: where should a newbie go...


Where can a newbie go to ask questions like "why do CW rigs have RIT,
is it common for there to be a frequency offset between the two
operators in a CW QSO or what" and so forth. I live in a rural area and
don't think I will be able to blend in with the local ham club. Is
there some nook of the internet where newbie Q&A is welcome?

--
-30-
  #2   Report Post  
Old August 6th 07, 05:26 PM posted to rec.radio.amateur.antenna
external usenet poster
 
First recorded activity by RadioBanter: Mar 2007
Posts: 120
Default non-antenna question: where should a newbie go...


"Anonymous" wrote in message
...

Where can a newbie go to ask questions like "why do CW rigs have RIT,
is it common for there to be a frequency offset between the two
operators in a CW QSO or what" and so forth. I live in a rural area and
don't think I will be able to blend in with the local ham club. Is
there some nook of the internet where newbie Q&A is welcome?

--
-30-


This group is for antennas - so suggest you use
rec.radio.amateur.equipment news group.

News groups for Ham radio and their useage are listed at URL:
http://ac6v.com/newsgroups.htm

To answer your question about RIT useage on CW

RIT. Receiver Incremental Tuning (Clarifier on some rigs) allows you to
receive slightly above or below your transmit frequency. For DXing, it is
typically used for CW split pileups - set your main dial to 2 to 5 kHz up
from the DX station and use RIT to hear the DX station. This allows the DX
station to spread out the callers and prevents chaos on the DX frequency.



If an SSB DX station is operating with a small split, the RIT range may
allow you to use RIT to achieve the split. RIT typically covers +/- 5 kHz or
+/- 10 kHz and is frequently used for CW split operating, but not often in
an SSB split operation.



Another use for RIT is when you wish to transmit on a given frequency and
the station you are receiving is off frequency or drifts away or starts
chasing you by retuning as you tune on them. Rather than change the main
tuning dial (thus your transmit frequency) use RIT. The Main Tuning dial
determines the transmit frequency and the RIT determines the receive
frequency.



There are several good books that will explain DXing, operating, and
transceiver controls-- use google to search for Amateur Radio DX Books



Good Luck -- see you at rec.radio.amateur.equipment

Lamont



  #3   Report Post  
Old August 6th 07, 06:28 PM posted to rec.radio.amateur.antenna
external usenet poster
 
First recorded activity by RadioBanter: Aug 2007
Posts: 1
Default non-antenna question: where should a newbie go...

In article , Anonymous
wrote:

some nook of the internet where newbie Q&A is welcome?


hamforum.com is relatively friendly to newbies ... well-crafted Google
searches will also dig up the answer to almost any question.
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
newbie UHF antenna question Mike Antenna 7 June 16th 06 08:54 PM
Newbie Ham question: Antenna (Diamond X-50) Dave Bushong General 6 November 25th 04 04:23 PM
Newbie antenna question (T2FD) Scott Mayo Shortwave 6 November 10th 04 04:59 AM
Newbie SWL question: Antenna geometry Hidalgo Shortwave 5 June 8th 04 04:47 AM
TV antenna question , newbie cme Antenna 1 February 5th 04 05:03 PM


All times are GMT +1. The time now is 06:49 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017