I'm looking for plans to build a balanced tuner for ladderline without a
balun. In the past, I've seen schematics for tuners with ganged
inductors. Can't seem to stumble back upon these on a web search. Any
ideas and thanks in advance.

Gary

On Sun, 27 Mar 2005 11:44:58 -0800, Angela & Gary
wrote:



I'm looking for plans to build a balanced tuner for ladderline without a
balun. In the past, I've seen schematics for tuners with ganged
inductors. Can't seem to stumble back upon these on a web search. Any
ideas and thanks in advance.

Gary

See

http://www.somis.org/bbat.html

But it still requires a balun. If you wish to use no balun then you'll
need to build a link type tuner.

Danny, K6MHE

In article ,
Angela & Gary wrote:

I'm looking for plans to build a balanced tuner for ladderline without a
balun. In the past, I've seen schematics for tuners with ganged
inductors. Can't seem to stumble back upon these on a web search. Any
ideas and thanks in advance.

You'll need some form of inductively coupled ("link-coupled") tuner to
do this. The most popular of these at the moment seems to be the
"Z-match" - it has good although not perfect current balance on the
outputs.

Most of the Z-match designs I've seen can be implemented with two
variable capacitors, and one fixed inductor. There's a "two coil"
Z-match but I gather that it doesn't really have advantages over the
one-coil variety. The coils can be either air-wound, or wound on a
powdered-metal toroid.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!

There are a few balanced tuners available for purchase. I assume you
just want the building experience? If not, Johnson Matchbox tuners are
sometimes available on Ebay and other sites. And MFJ has two current
models. And Palstar has one current balanced tuner.

Good luck, jimbo

Angela & Gary wrote:
I'm looking for plans to build a balanced tuner for ladderline
without a
balun. In the past, I've seen schematics for tuners with ganged
inductors. Can't seem to stumble back upon these on a web search.
Any
ideas and thanks in advance.

Gary

You'll need a balun whether or not you use a balanced tuner.

That is unless you have a balanced transmitter.

You can save yourself the cost of a pair of ganged inductors by
inserting a choke balun between the balanced feedline and an ordinary
unbalanced tuner.
----
Reg

In article ,
Reg Edwards g4fgq,regp@ZZZbtinternet,com wrote:

You'll need a balun whether or not you use a balanced tuner.

That is unless you have a balanced transmitter.

.... or a link-coupled tuner, which works just fine without a balun
(or, looked at in another way, incorporates a balun as part of its
basic design).

You can save yourself the cost of a pair of ganged inductors by
inserting a choke balun between the balanced feedline and an ordinary
unbalanced tuner.

.... and being very careful to "float" the chassis of the tuner clear
of ground, and insulate it thoroughly.. If you don't do this, your
ground connection bypasses the choke balun, and/or you can be "bitten"
by the RF on the chassis which will often be at a substantial
potential above ground.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!

The whole purpose of the choke balun is to allow the ordinary tuner to
be safely grounded.

The tuner is grounded automatically by virtue of its short connection
to the unbalanced transmitter.

Or have I misunderstood you?
----
Reg

In article ,
Reg Edwards g4fgq,regp@ZZZbtinternet,com wrote:

The whole purpose of the choke balun is to allow the ordinary tuner to
be safely grounded.

The tuner is grounded automatically by virtue of its short connection
to the unbalanced transmitter.

Or have I misunderstood you?

It depends. There are two arrangements using choke baluns that I'm
aware of - balun at the input, and balun at the output.

It's fairly common to put a choke balun at the output of an unbalanced
tuner, to convert the unbalanced output to a balanced form. This
seems to work pretty well when the tuner is looking into loads that
aren't too high, low, or reactive in nature. For high-R or
highly-reactive loads, it may be difficult to create a choke balun
with a high enough choking reactivity to force adequate balance on the
line. In this approach, the tuner can be connected to the transceiver
via a direct cable, and its chassis can be connected to the station RF
ground.

The other approach is to put a choke balun at the input of the tuner,
"float" the tuner chassis clear of ground, and connect the balanced
line directly to the "unbalanced" output of the tuner. This
pseudo-balanced arrangment can provide good balance once the tuner is
adjusted, because the balun "sees" 50 ohms on both sides... but it
adds the complication of having to float and insulate the tuner. I've
heard of some people taking a commercial tuner, and putting it on
insulators inside a secondary outer chassis. The outer chassis can be
connected to the station ground, and or to the transceiver coaxial
feedline braid _before_ going through the choke balun.

--
Dave Platt AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!

Dave Platt wrote:
In article ,
Reg Edwards g4fgq,regp@ZZZbtinternet,com wrote:


The whole purpose of the choke balun is to allow the ordinary tuner to
be safely grounded.

The tuner is grounded automatically by virtue of its short connection
to the unbalanced transmitter.

Or have I misunderstood you?


It depends. There are two arrangements using choke baluns that I'm
aware of - balun at the input, and balun at the output.

It's fairly common to put a choke balun at the output of an unbalanced
tuner, to convert the unbalanced output to a balanced form. This
seems to work pretty well when the tuner is looking into loads that
aren't too high, low, or reactive in nature. For high-R or
highly-reactive loads, it may be difficult to create a choke balun
with a high enough choking reactivity to force adequate balance on the
line. In this approach, the tuner can be connected to the transceiver
via a direct cable, and its chassis can be connected to the station RF
ground.

The other approach is to put a choke balun at the input of the tuner,
"float" the tuner chassis clear of ground, and connect the balanced
line directly to the "unbalanced" output of the tuner. This
pseudo-balanced arrangment can provide good balance once the tuner is
adjusted, because the balun "sees" 50 ohms on both sides... but it
adds the complication of having to float and insulate the tuner. I've
heard of some people taking a commercial tuner, and putting it on
insulators inside a secondary outer chassis. The outer chassis can be
connected to the station ground, and or to the transceiver coaxial
feedline braid _before_ going through the choke balun.

Hi Dave and all,

For Reg. I've used the method that Dave speaks of above over the years
with very good Sucess but as he says the tuner must be isolated from
ground in order to produce the needed balance at the out put. The
advatage as stated is that the Balun (once the turner is tuned to the
frequency being used will see pretty much 50 ohms on both sides. It has
work very well here .

73 Dave Kc1di

Angela & Gary wrote:
I'm looking for plans to build a balanced tuner for ladderline without a
balun. In the past, I've seen schematics for tuners with ganged
inductors. Can't seem to stumble back upon these on a web search. Any
ideas and thanks in advance.

Gary
Hi Gary,

you may find the following web sites of interest in designing your own
balanced tuner.
hope they help in your quest.
73 Dave KC1DI

http://www.cebik.com/link/link.html

http://www.cebik.com/edu/edu6.html

http://www.cebik.com/link/l-bal.html

another approach is the Z-Match tuner

http://www.qsl.net/wb3gck/zmatch.htm

http://www4.tpgi.com.au/users/ldbutl...CoilZMatch.htm

(Note it is very desirable on the Z-Match to have Vernier dials as the
Adjustments can be very sharp and easy to miss without them.)

http://www.seboldt.net/k0jd/z-match.html#schematic