Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts, but
I need to rewire it for 110 volts, is there anyone out there that can tell
me how to do this,,Thank you

"Barry" wrote:
Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts,
but I need to rewire it for 110 volts, is there anyone out there that can
tell me how to do this,,Thank you

If you don't find your answer here try your question on eHam.net.

Go Cavs.

Hello Barry:

Most all of the ham amps have two 110 Volt AC windings in the power
transformer. These two seperate windings are wired in seriers like two
batteries in a flashlight. This series connection allows for the 220
Volt AC use.

The two seperate windings can also be wired for 110 Volt AC use. They
need to be wired in paralell. This is not a terribable hard thing to do.
I am sure the operators manual will show how both the 220 and 110
connections are made. Manuals can be bought off the internet, just type
in Dentron Clipperton into www.Google.com

Hope this helps

Jay in the Mojave



Barry wrote:

Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts, but
I need to rewire it for 110 volts, is there anyone out there that can tell
me how to do this,,Thank you

Hello Barry: again...

Go to the CB Tricks web site at:
http://www.cbtricks.com/Amp/dentron/...on_l/index.htm

You find will a diagram showing how to wire the amp for 110 Volt use. If
this is out of your technical league I would have a technician do it for
you. Remember this amp uses high voltages that can and have killed.

Jay in the Mojave


Barry wrote:

Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts, but
I need to rewire it for 110 volts, is there anyone out there that can tell
me how to do this,,Thank you

"Jay in the Mojave" wrote in message
...
Hello Barry: again...

Go to the CB Tricks web site at:
http://www.cbtricks.com/Amp/dentron/...on_l/index.htm

You find will a diagram showing how to wire the amp for 110 Volt use. If
this is out of your technical league I would have a technician do it for
you. Remember this amp uses high voltages that can and have killed.

Jay in the Mojave

At the very least, get into the HV section and you'll have a nice blue aura.

Thank you jay, and you too yo,,,,
"Jay in the Mojave" wrote in message
...
Hello Barry: again...

Go to the CB Tricks web site at:
http://www.cbtricks.com/Amp/dentron/...on_l/index.htm

You find will a diagram showing how to wire the amp for 110 Volt use. If
this is out of your technical league I would have a technician do it for
you. Remember this amp uses high voltages that can and have killed.

Jay in the Mojave


Barry wrote:

Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts,
but
I need to rewire it for 110 volts, is there anyone out there that can
tell
me how to do this,,Thank you

On Jun 2, 7:29 pm, "Barry" wrote:
Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts, but
I need to rewire it for 110 volts, is there anyone out there that can tell
me how to do this,,Thank you

Keyclown activity with amps is illegal.

Hello Barry:

Those are good work horse linear amplifiers.

Jay in the Mojave


Barry wrote:
Thank you jay, and you too yo,,,,
"Jay in the Mojave" wrote in message
...

Hello Barry: again...

Go to the CB Tricks web site at:
http://www.cbtricks.com/Amp/dentron/...on_l/index.htm

You find will a diagram showing how to wire the amp for 110 Volt use. If
this is out of your technical league I would have a technician do it for
you. Remember this amp uses high voltages that can and have killed.

Jay in the Mojave


Barry wrote:


Hello, I have a Dentron Clipperton Qro linear, it's setup for 220 volts,
but
I need to rewire it for 110 volts, is there anyone out there that can
tell
me how to do this,,Thank you