Hello Stevo:

Ok yeah it can handle a bunch of them all righty.

Its good for 10KW RMS. Put the I-25K Bracket and LC Connector to hanle
even more power. Hammer down dude!

Jay


Steveo wrote:
Steveo wrote:

Vinnie S. wrote:

The Imax is kicking butt. I made my first Ham contact on 10 meters in
Texas. When I told him he was my first ham contact, he got more excited
than I got. I figured after coax losses, I am probably only getting out
15-20 watts on SSB. I am only getting out 6 watts on AM.

As far as CB and locals, they couldn't believe it was me because they
barely heard me with the Firestik in the attic. This Imax seems to
excel on receive. It is super quiet with no static.

Vinnie S.


Sounds like it's time for a 30L1 or similar. Hows the tvi/rf looking?


Hey Jay, reckon his antenna can handle a 30L1?

Jay in the Mojave wrote:
Hello Stevo:

Ok yeah it can handle a bunch of them all righty.

Its good for 10KW RMS. Put the I-25K Bracket and LC Connector to hanle
even more power. Hammer down dude!

Jay

Hi Jay, I was speaking of Vinnie's Imax. I don't know what they are rated
for.

I already know your antenna can handle it and more!


Steveo wrote:
Steveo wrote:

Vinnie S. wrote:

The Imax is kicking butt. I made my first Ham contact on 10 meters in
Texas. When I told him he was my first ham contact, he got more
excited than I got. I figured after coax losses, I am probably only
getting out 15-20 watts on SSB. I am only getting out 6 watts on AM.

As far as CB and locals, they couldn't believe it was me because they
barely heard me with the Firestik in the attic. This Imax seems to
excel on receive. It is super quiet with no static.

Vinnie S.


Sounds like it's time for a 30L1 or similar. Hows the tvi/rf looking?


Hey Jay, reckon his antenna can handle a 30L1?

On 18 Jun 2005 10:16:05 GMT, Steveo wrote:

Jay in the Mojave wrote:
Hello Stevo:

Ok yeah it can handle a bunch of them all righty.

Its good for 10KW RMS. Put the I-25K Bracket and LC Connector to hanle
even more power. Hammer down dude!

Jay

Hi Jay, I was speaking of Vinnie's Imax. I don't know what they are rated
for.

I already know your antenna can handle it and more!


According to the manual, it is tested at 5,000 watts. Sounds rather high.

Vinnie S.

Vinnie i have three I-Max 2000 That the center section cap flashed over
causing very bad TVI SWR ok. I cut them open and that is what i found.
They worked ok with the RCI 2990 But when i used the X Force 612 hd the
center section cap would flash over and carbon track.
I do not know what this cap is for
I asked on this group but couldnot get any help. I run the amp at 500 w
and pep 1000. I have ordered a WOLF point 64 11 M. No coils or caps to
burn out.
When I get time I am going to elimenate the cap and see what happins.

Triple 5
Trip 555
BIG in TEXAS

On Tue, 21 Jun 2005 14:11:17 -0600, (H Nelson BIG in
TEXAS!!!!) wrote:

Vinnie i have three I-Max 2000 That the center section cap flashed over
causing very bad TVI SWR ok. I cut them open and that is what i found.
They worked ok with the RCI 2990 But when i used the X Force 612 hd the
center section cap would flash over and carbon track.
I do not know what this cap is for
I asked on this group but couldnot get any help. I run the amp at 500 w
and pep 1000. I have ordered a WOLF point 64 11 M. No coils or caps to
burn out.
When I get time I am going to elimenate the cap and see what happins.

Triple 5
Trip 555
BIG in TEXAS
*******

Inserting reactive components in the antenna has the effect of
lengthening or shortening the electrical length of the antenna. IF the
antenna is physically less than a quarter wave an inductive load is
added anywhere between the feed point and the end of the antenna to
effectively make it a quarter wave antenna electrically. Capacitive
loads do the reverse. They take physically long antenna, a quarter
wave, and shorten them electrically.

All reactive loads alter feed point impedance and the "Q" or bandwidth
of an antenna. If my memory serves me correctly the IMAX is
essentially an end fed 5/8 wave antenna. FOr Solarcon to use the same
feed system that they do on the A99, they must raise the feed
impedance. This can easily be done by inserting a capacitor anywhere
in the antenna. Preferable this should be about a 1/4 from the feed
point. That is where the current in the antenna is at maximum. The
volatge the the cap must withstand is a minimum.

Removing the cap will most likely screw up the matching of the
antenna.

james

Triple 5 in TX, give me an email at

Vinnie S. wrote:
On 18 Jun 2005 10:16:05 GMT, Steveo wrote:

Jay in the Mojave wrote:
Hello Stevo:

Ok yeah it can handle a bunch of them all righty.

Its good for 10KW RMS. Put the I-25K Bracket and LC Connector to hanle
even more power. Hammer down dude!

Jay

Hi Jay, I was speaking of Vinnie's Imax. I don't know what they are
rated for.

I already know your antenna can handle it and more!

According to the manual, it is tested at 5,000 watts. Sounds rather high.

Vinnie S.

Does it matter that it's in a tree?

On 23 Jun 2005 00:57:37 GMT, Steveo wrote:


Hi Jay, I was speaking of Vinnie's Imax. I don't know what they are
rated for.

I already know your antenna can handle it and more!

According to the manual, it is tested at 5,000 watts. Sounds rather high.

Vinnie S.

Does it matter that it's in a tree?

Only if you want to see a huge forest fire !!!

Vinnie S.

On Wed, 22 Jun 2005 21:38:28 -0400, Vinnie S. wrote:

On 23 Jun 2005 00:57:37 GMT, Steveo wrote:


Hi Jay, I was speaking of Vinnie's Imax. I don't know what they are
rated for.

I already know your antenna can handle it and more!

According to the manual, it is tested at 5,000 watts. Sounds rather high.

Vinnie S.

Does it matter that it's in a tree?

Only if you want to see a huge forest fire !!!

Vinnie S.


Moped, I hit Guadalajara, Mexico with my whopping 15 watts on 28.380 !!!!

The dude was speaking at 100 MPH.

Vinnie S.

Vinnie S. wrote:
Moped, I hit Guadalajara, Mexico with my whopping 15 watts on 28.380 !!!!

The dude was speaking at 100 MPH.

Vinnie S.

How fast can ya say mama la pinga pato?? hehe