Would someone please give me the wiring for the Icom IC-725. Also ACC1
wiring if possible. I have misplaced my manual.

Tnx de WN5GDV

Bill, the following should help.

Front panel view of 8 pin chassis mic connector.

Indent located at 12o'clock position, working anti-clockwise.

Pin 1=Mic input
Pin 2=+8v @10mA dc output
Pin 3=Freq up/down (Ground direct for up, or via 470 ohm)
Pin 4=Squelch switch (open=low,closed=high)
Pin 5=PTT
Pin 6=Gnd (PTT)
Pin 7=Gnd (Mic ground)
Pin 8=AF output (Middle pin)

Icom warning, do not short Pin2 to gnd. Damage to 8v regulator will occur.

Taken from Icom manual
good luck, Roger G7JAQ

PS, for MIKE read MIC

--


----------------------------------------------------
This mailbox protected from junk email by Matador
from MailFrontier, Inc. http://info.mailfrontier.com

Bill,
info on ACC(1) 8pin din, rear mounted socket as follows

Indent (ground) located at 12 o'clock. Rear panel view.

Working clockwise from indent.
Pin 6=D=Squelch input.
Pin 1=No connection.
Pin 4=A= Screened AFSK Input.
Pin 2=B=AFSK Screen gnd.
Pin 5=C=AF Input.
Pin 3=E=PTT.
Pin 7=No connection.

regards,
Roger, G7JAQ

--


----------------------------------------------------
This mailbox protected from junk email by MailFrontier Desktop
from MailFrontier, Inc. http://info.mailfrontier.com

Bill Murcheski wrote:


Would someone please give me the wiring for the Icom IC-725. Also ACC1
wiring if possible. I have misplaced my manual.

Tnx de WN5GDV

Hello, Bill.

You can download the manual as a PDF by following the link at
http://www.icom.co.jp/world/products/amateur/index.htm

HTH
--
To design the perfect anti-Unix, write an operating system that thinks
it knows what you're doing better than you do. And then adds injury to
insult by getting it wrong.
- esr

Bill, the following should help.

Front panel view of 8 pin chassis mic connector.

Indent located at 12o'clock position, working anti-clockwise.

Pin 1=Mic input
Pin 2=+8v @10mA dc output
Pin 3=Freq up/down (Ground direct for up, or via 470 ohm)
Pin 4=Squelch switch (open=low,closed=high)
Pin 5=PTT
Pin 6=Gnd (PTT)
Pin 7=Gnd (Mic ground)
Pin 8=AF output (Middle pin)

Icom warning, do not short Pin2 to gnd. Damage to 8v regulator will occur.

Taken from Icom manual
good luck, Roger G7JAQ

PS, for MIKE read MIC

--


----------------------------------------------------
This mailbox protected from junk email by Matador
from MailFrontier, Inc. http://info.mailfrontier.com

Bill,
info on ACC(1) 8pin din, rear mounted socket as follows

Indent (ground) located at 12 o'clock. Rear panel view.

Working clockwise from indent.
Pin 6=D=Squelch input.
Pin 1=No connection.
Pin 4=A= Screened AFSK Input.
Pin 2=B=AFSK Screen gnd.
Pin 5=C=AF Input.
Pin 3=E=PTT.
Pin 7=No connection.

regards,
Roger, G7JAQ

--


----------------------------------------------------
This mailbox protected from junk email by MailFrontier Desktop
from MailFrontier, Inc. http://info.mailfrontier.com

Bill Murcheski wrote:


Would someone please give me the wiring for the Icom IC-725. Also ACC1
wiring if possible. I have misplaced my manual.

Tnx de WN5GDV

Hello, Bill.

You can download the manual as a PDF by following the link at
http://www.icom.co.jp/world/products/amateur/index.htm

HTH
--
To design the perfect anti-Unix, write an operating system that thinks
it knows what you're doing better than you do. And then adds injury to
insult by getting it wrong.
- esr