Ugh! It's very similar to a power supply I worked on in the
mid-1970's for a tacan pulse power calibration system. The
scars had almost healed. There's not much advantage in it
over a vintage blood and thunder supply beyond improved
regulation. No reduction in the amount of steel or output
capacitance needed... lots of stored energy.

Though I did learn a lot about PUT's and SCR's in the process
so overall it was fun. It's also when I learned that power
supply engineers always run Towards the explosion.


steve H
http://www.realhamradio.com/hvreg.pdf

for a schematic.

On Sep 15, 8:09*pm, Grumpy The Mule wrote:
Ugh! *It's very similar to a power supply I worked on in the
mid-1970's for a tacan pulse power calibration system. *The
scars had almost healed. *There's not much advantage in it
over a vintage blood and thunder supply beyond improved
regulation. *No reduction in the amount of steel or output
capacitance needed... lots of stored energy.

Though I did learn a lot about PUT's and SCR's in the process
so overall it was fun. It's also when I learned that power
supply engineers always run Towards the explosion. *

steve H



http://www.realhamradio.com/hvreg.pdf

for a schematic.- Hide quoted text -

- Show quoted text -

I dont suppose there is an SMPS pwer supply design book for dummies
ou t there somwhere.
Seriously what would be a good book for transformer design. I
downloaded the info ferroxcube had. I was hoping they had someready
made transformers. I know they have made some for the military/gov,
but I didnt see anything off the shelf available except their cores.


Jimmie.

Howdy,


It's a tough choice, most of the books in the subject have at
least a couple of strong points or useful tricks.

If I could have only one book and it had to cover all aspects of
SMPS design I'd chose "Switching Power Supply Design" by Abraham
L. Pressman.

There are many individual books devoted to topology convolution,
wound magnetics design, control systems engineering and the care and
feeding of semiconductor switches. So no one book covers evey
aspect thoughoughly but Abe's book is pretty good.

He also wrote "Switching And Linear Power Supply Design, power
Converter Design", which was his first book. Worth having for
sometimes you might need a big linear supply.

"Switchmode Power Supply Handbook" by Keith Billings contains many
practical tips.

For magetics "Transformer And Inductor Design Handbook" by Colonel Wm.
T. McLyman is good. Another good book is Magnetics Engineering
Fundamentals and Computer Aided Design" by Fred M. Lillenstein.

"Transformers for Electronic Circuits" by Nathan Grossner is good
too, especially for heavy metal. There is a copy of it online
at some tube audio site but I can't find the link off hand.

Also check the free software and app notes at Magnetics Inc.
And at Micrometals Inc. too.

Some decent vendors of needed odds and ends are Pleo, lodestone
pacific, Robison Ind.,Dexter, MH&W. CWS Coil Winding Services
is worth checking out too.

For built transformers you'll mostly find low voltage and
telecom stuff off the shelf. Can't recall seeing any high
power (more than a couple of hundred watts) high voltage
transformers off the shelf. Even low power HV stuff is rare
unless you count the measly few hundreds of volts for EL
and neon lighting.

I really think this is a roll your own kind of affair. Furukawa
TEX-E triple insulated wire might be handy without a segmented
secondary bobbin.

I hope you find some of this useful. There are a LOT of books on
these subjects. Enough to cause my house to sag under the weight.



I dont suppose there is an SMPS pwer supply design book for dummies
ou t there somwhere.
Seriously what would be a good book for transformer design. I
downloaded the info ferroxcube had. I was hoping they had someready
made transformers. I know they have made some for the military/gov,
but I didnt see anything off the shelf available except their cores.


Jimmie.

On Sep 16, 8:15*pm, Grumpy The Mule wrote:
Howdy,

It's a tough choice, most of the books in the subject have at
least a couple of strong points or useful tricks.

If I could have only one book and it had to cover all aspects of
SMPS design I'd chose "Switching Power Supply Design" by Abraham
L. Pressman. *

There are many individual books devoted to topology convolution,
wound magnetics design, control systems engineering and the care and
feeding of semiconductor switches. *So no one book covers evey
aspect thoughoughly but Abe's book is pretty good. *

He also wrote "Switching And Linear Power Supply Design, power
Converter Design", which was his first book. *Worth having for
sometimes you might need a big linear supply.

"Switchmode Power Supply Handbook" by Keith Billings contains many
practical tips.

For magetics "Transformer And Inductor Design Handbook" by Colonel Wm.
T. McLyman is good. *Another good book is Magnetics Engineering
Fundamentals and Computer Aided Design" by Fred M. Lillenstein.

"Transformers for Electronic Circuits" by Nathan Grossner is good
too, especially for heavy metal. *There is a copy of it online
at some tube audio site but I can't find the link off hand.

Also check the free software and app notes at Magnetics Inc.
And at Micrometals Inc. too. *

Some decent vendors of needed odds and ends are Pleo, lodestone
pacific, Robison Ind.,Dexter, MH&W. CWS *Coil Winding Services
is worth checking out too.

For built transformers you'll mostly find low voltage and
telecom stuff off the shelf. *Can't recall seeing any high
power (more than a couple of hundred watts) high voltage
transformers off the shelf. *Even low power HV stuff is rare
unless you count the measly few hundreds of volts for EL
and neon lighting.

I really think this is a roll your own kind of affair. Furukawa
TEX-E triple insulated wire might be handy without a segmented
secondary bobbin.

I hope you find some of this useful. *There are a LOT of books on
these subjects. *Enough to cause my house to sag under the weight.



I dont suppose there is an SMPS pwer supply design book for dummies
ou t there somwhere.
Seriously what would be a good book for transformer design. I
downloaded the info ferroxcube had. I was hoping they had someready
made transformers. I know they have made some for the military/gov,
but I didnt see anything off the shelf available except their cores.

Jimmie.- Hide quoted text -

- Show quoted text -

My big problem at the moment is designinging a transformer. after much
reading in the last couple of days I am begining to think it is not
the big deal I thought it was. Since I am not trying to build 50k
units I dont have to use the cheapest thing I can get by with and can
overdesign a bit. I can see that just a few cores may take care of all
of my needs. Oh well its back to work so it will be a few days before
i get to piddle with this anymore. One of my jobs this week is to go
through all the old UPSs we have in the store room and find out which
ones are good and chunk the rest.

Jimmie

Howdy,

I found the URL for Grossner's book online.
http://tinyurl.com/3z7mxv


It seems to me that using the inverter oven transformer
and IGBT with a flyback controller like UC3842 might work.

Just a straight enough, hard-switched, flyback with single
ended output. You'd "only" get 1.5-2KV out less output power
maybe one half to three quarters as much... but that's not bad.

Mmm! Old UPS's have lots of good parts in them, especially
the ones with big 60Hz transformers and big heatsinks. Chuck
them into the trunk of your automobile.




My big problem at the moment is designinging a transformer. after much
reading in the last couple of days I am begining to think it is not
the big deal I thought it was. Since I am not trying to build 50k
units I dont have to use the cheapest thing I can get by with and can
overdesign a bit. I can see that just a few cores may take care of all
of my needs. Oh well its back to work so it will be a few days before
i get to piddle with this anymore. One of my jobs this week is to go
through all the old UPSs we have in the store room and find out which
ones are good and chunk the rest.

Jimmie

On Sep 17, 7:59*pm, Grumpy The Mule wrote:
Howdy,

I found the URL for Grossner's book online.http://tinyurl.com/3z7mxv

It seems to me that using the inverter oven transformer
and IGBT with a flyback controller like UC3842 might work.

Just a straight enough, hard-switched, flyback with single
ended output. *You'd "only" get 1.5-2KV out less output power
maybe one half to three quarters as much... but that's not bad.

Mmm! *Old UPS's have lots of good parts in them, especially
the ones with big 60Hz transformers and big heatsinks. *Chuck
them into the trunk of your automobile.



My big problem at the moment is designinging a transformer. after much
reading in the last couple of days I am begining to think it is not
the big deal I thought it was. Since I am not trying to build 50k
units I dont have to use the cheapest thing I can get by with and can
overdesign a bit. I can see that just a few cores may take care of all
of my needs. Oh well its back to work so it will be a few days before
i get to piddle with this anymore. One of my jobs this week is to go
through all the old UPSs we have in the store room and find out which
ones are good and chunk the rest.

Jimmie- Hide quoted text -

- Show quoted text -



I was reading up on push-pull topology of switching power supplies
and see that they have problems with flux imbalance. I used to work on
some power supplies that were push pull when I was in the USAF and the
driver transistors were always failing, now I know why. I see that
this isnt as much of a problem for FETs, How about IGBTs.


Jimmie

Short answer, IGBTs are much better but not as good as MOSFETs.
In many cases they're good enough that the turn-off tail can be
ignored with very minor accommodation if any. In some cases an
IGBT may be superior than a MOSFET because you don't have to worry
about the switches RDSon drifting apart with temperature.

Though now days you can buy a 75V 120A 0.0004 Ohm MOSFET in a
T0-220 package... I guess RDSon isn't much of an issue.

The main problem with both IGBT and regular old bipolar transistors
in a push-pull circuit is the turn-off tail. The MOSFET does not
have a turn-off tail. There are two classes of IGBT, punch-though
and non-punch through. The punch-trough devices have better turn-off
times but are more fragile. Lately I've been using Trench Field Stop
IGBT's and they're very good.

There are several means of preventing imbalance of the transformer
in driven (not self oscillating) converters. The PWM will adjust
the on-time to compensate for the tail as it regulates the output
voltage. You can sense the differences with a circuit that converts
time to voltage (a capacitor and a current source) then make the
correction.

There are clever flux balancing windings that can be added. One
Unitrode app note describes how this can be done in the course of
presenting a half-bridge power converter. I can't recall the
document number.

In the half bridge and full bridge sometimes a capacitor in series
with the primary wdinding prevents saturation. I think you could
build a two capacitor divider across the input voltage and at the
center connect your transformer centertap lead. Then as the
imbalance increases the voltage at the center tap with shift
to compensate for it. I've seen half bridges built this way...
might work for a push pull... just guessing as I've never tried it.

A very small gap (0.001-0.003") will prevent saturation if the
imbalance is minor and not decrease the magnetizing inductance
too much. Sometimes any decrease is unwelcome though.
A distributed gap material like powdered-iron, koolmu, MPP
or sendust, might be useful if you expect to have flux imbalance
problems.

Pulse by pulse current limiting will mask the problem, so the
transformer is in saturation but not far into it and the current
limit keeps it from destroying the switches. Kinda risky to rely
on this alone but it's helpful combined with other measures.

In a current fed converter the transformer may saturate and then
switches are effectively connected directly to the current source.
No harm done! A current fed push-pull is a rugged topology. The
VAX8800 computer uses one for its control and start-up power supply.


I was reading up on push-pull topology of switching power supplies
and see that they have problems with flux imbalance. I used to work on
some power supplies that were push pull when I was in the USAF and the
driver transistors were always failing, now I know why. I see that
this isnt as much of a problem for FETs, How about IGBTs.


Jimmie

On Sep 18, 8:56*pm, Grumpy The Mule wrote:
Short answer, IGBTs are much better but not as good as MOSFETs.
In many cases they're good enough that the turn-off tail can be
ignored with very minor accommodation if any. *In some cases an
IGBT may be superior than a MOSFET because you don't have to worry
about the switches RDSon drifting apart with temperature. *

Though now days you can buy a 75V 120A 0.0004 Ohm MOSFET in a
T0-220 package... I guess RDSon isn't much of an issue.

The main problem with both IGBT and regular old bipolar transistors
in a push-pull circuit is the turn-off tail. *The MOSFET does not
have a turn-off tail. *There are two classes of IGBT, punch-though
and non-punch through. The punch-trough devices have better turn-off
times but are more fragile. *Lately I've been using Trench Field Stop
IGBT's and they're very good.

There are several means of preventing imbalance of the transformer
in driven (not self oscillating) converters. *The PWM will adjust
the on-time to compensate for the tail as it regulates the output
voltage. *You can sense the differences with a circuit that converts
time to voltage (a capacitor and a current source) then make the
correction.

There are clever flux balancing windings that can be added. *One
Unitrode app note describes how this can be done in the course of
presenting a half-bridge power converter. *I can't recall the
document number.

In the half bridge and full bridge sometimes a capacitor in series
with the primary wdinding *prevents saturation. *I think you could
build a two capacitor divider across the input voltage and at the
center connect your transformer centertap lead. *Then as the
imbalance increases the voltage at the center tap with shift
to compensate for it. I've seen half bridges built this way...
might work for a push pull... just guessing as I've never tried it.

A very small gap (0.001-0.003") will prevent saturation if the
imbalance is minor and not decrease the magnetizing inductance
too much. *Sometimes any decrease is unwelcome though. *
A distributed gap material like powdered-iron, koolmu, MPP
or sendust, might be useful if you expect to have flux imbalance
problems.

Pulse by pulse current limiting will mask the problem, so the
transformer is in saturation but not far into it and the current
limit keeps it from destroying the switches. *Kinda risky to rely
on this alone but it's helpful combined with other measures.

In a current fed converter the transformer may saturate and then
switches are effectively connected directly to the current source.
No harm done! *A current fed push-pull is a rugged topology. *The
VAX8800 computer uses one for its control and start-up power supply.



*I was reading up on push-pull topology of switching power supplies
and see that they have problems with flux imbalance. I used to work on
some power supplies that were push pull when I was in the USAF and the
driver transistors were always failing, now I know why. I see that
this isnt as much of a problem for FETs, How about IGBTs.

Jimmie- Hide quoted text -

- Show quoted text -

I work with a couple of pieces of equipment that synthesises a
repetitive waveform by playing back the waeform from a ROM. I thought
I could do something like this to control the on-off timing of the
IGBT. This would set a minimum time between turn on and turn off and
the rest would be controlled by PWM.

This is one advantage of the flyback and asymmetrical forward
converters. They will reset if there's enough dead time.
So in those cases your ROM circuit would do the trick.

Symmetrical topologies like push-pull, half-bridge and
full-bridge can saturate even if there is plenty of dead
time. The core is always being driven by the control
circuit, so it has no time to relax, If the drive isn't
equal and opposite for each half cycle there is an offset
which the core accumulates. Eventually it will saturate.
unless there is some means to compensate for the imbalance
of the drive (like a coupling capacitor.)
So here the ROM circuit will not help.



wrote in news:8e344554-a8d0-4796-ae20-
:

I work with a couple of pieces of equipment that synthesises a
repetitive waveform by playing back the waeform from a ROM. I thought
I could do something like this to control the on-off timing of the
IGBT. This would set a minimum time between turn on and turn off and
the rest would be controlled by PWM.

On Sep 19, 11:57*am, Grumpy The Mule wrote:
This is one advantage of the flyback and asymmetrical forward
converters. *They will reset if there's enough dead time.
So in those cases your ROM circuit would do the trick.

Symmetrical topologies like push-pull, half-bridge and
full-bridge can saturate even if there is plenty of dead
time. * The core is always being driven by the control
circuit, so it has no time to relax, *If the drive isn't
equal and opposite for each half cycle there is an offset
which the core accumulates. *Eventually it will saturate.
unless there is some means to compensate for the imbalance
of the drive (like a coupling capacitor.)
So here the ROM circuit will not help.

wrote in news:8e344554-a8d0-4796-ae20-
:



I work with a couple of pieces of equipment that synthesises a
repetitive waveform by playing back the waeform from a ROM. I thought
I could do something like this to control the on-off timing of the
IGBT. This would set a minimum time between turn on and turn off and
the rest would be controlled by PWM.- Hide quoted text -

- Show quoted text -

I think I get it. Would this explain why in a push-pull topology after
the transistors have been replaced a couple of times the power supply
just keeps failing for no apparent reason?

Are you saying that in other topologies it doesnt saturate or that it
doesnt matter if it does?

Ordered Abe's book.

Jimmie