Home |
Search |
Today's Posts |
#31
![]() |
|||
|
|||
![]()
Its not a simple matter of matching the transmitter to the radiation
resistance. First a short antenna is going to have a capacitive reactance. You must add an equal amount of inductive reactance (a loading coil) in order to cancel the capacitive reactance and make the antenna resonant at the operating frequency. Then what the transmitter needs to match is the total load impedance of the antenna "system". The load impedance includes the radiation resistance plus the resistance of the loading inductance plus the ground losses. The hardest thing to get a handle on will be the ground losses. The physical size of the transmitter housing is a small portion of a wavelength and losses will change as you handle the unit. |
#32
![]() |
|||
|
|||
![]()
Paul Burridge wrote:
... the best way to couple it to a PA with a 140 ohm output impedance? Use a loading coil to resonate the antenna to 40MHz. Use a transformer or tank circuit to transform the impedance. -- 73, Cecil http://www.qsl.net/w5dxp -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19 Different Servers! =----- |
#33
![]() |
|||
|
|||
![]()
Paul Burridge wrote:
... the best way to couple it to a PA with a 140 ohm output impedance? Use a loading coil to resonate the antenna to 40MHz. Use a transformer or tank circuit to transform the impedance. -- 73, Cecil http://www.qsl.net/w5dxp -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19 Different Servers! =----- |
#34
![]() |
|||
|
|||
![]()
On Tue, 09 Dec 2003 00:04:00 +0000, Paul Burridge wrote:
On Mon, 8 Dec 2003 21:32:52 +0000 (UTC), "Reg Edwards" wrote: I can see from the way you have made your enquiry you havn't the foggiest idea about what you are trying to accomplish. Do you know the frequency? What transmitter power output do you have in mind - 10 milliwatts or 1KW? For starters forget all about folding anything - you've been reading the wrong books. However you now mention a short whip above a groundplane of unknown construction. Perhaps you didn't see the earlier posts on the subject. The frequency is 40Mhz (radio control band) and the tx output stage as it stands puts out maximum power of 475mW with a 140 ohm resistor as load. I only *need* 50mW ERP., however, so can stand to see quite a bit of loss from an inefficient antenna. The antenna I will be using is a telescopic whip - exactly the same set-up as you see with model vehicle radio control transmitters- which is what it is, in fact. It ain't rocket science. Someone out there must know the radiation resistance of such a telescopic whip (which has a ground plane of just around 16 square inches contained within the remote control handset) and the best way to couple it to a PA with a 140 ohm output impedance? You have had quite a few answers which seem pretty good to me. I have a few comments. Stop saying "radiation resistance" and start saying "input impedance" or "feed impedance." Once you know the input impedance, getting maximum power transfer is a straightforward matching problem that can be solved in a variety of ways. True, you won't know for sure how much power is "getting out," but some of the posts in this thread have given you some estimates. If that isn't good enough, then you will have to measure by putting a receive antenna in the far field. Anyway, if you want to measure the input impedance, you should be able to do it with a two-channel oscilloscope and a 40 MHz function generator. Drive the antenna with the function generator and simultaneously measure the input voltage and current, including the phase relationship between them. The input impedance is V/I. To measure the current, put a suitably sized resistor in series with the antenna and measure the voltage across it. The voltage across the resistor should be small compared to the voltage into the antenna. If it is too small to see, use a bigger resistor until you can see it. Make sure both oscilloscope probes are grounded in the same place. Unless you have a differential probe (in which case, use it to measure the voltage across the current sensing resistor). From what others have already said, it sounds like the input will be extremely capacitive with a small series resistance. Once you know the details, however, it will be easy to tell you how to match this to your amplifier. That's my $0.02. Mac |
#35
![]() |
|||
|
|||
![]()
On Tue, 09 Dec 2003 00:04:00 +0000, Paul Burridge wrote:
On Mon, 8 Dec 2003 21:32:52 +0000 (UTC), "Reg Edwards" wrote: I can see from the way you have made your enquiry you havn't the foggiest idea about what you are trying to accomplish. Do you know the frequency? What transmitter power output do you have in mind - 10 milliwatts or 1KW? For starters forget all about folding anything - you've been reading the wrong books. However you now mention a short whip above a groundplane of unknown construction. Perhaps you didn't see the earlier posts on the subject. The frequency is 40Mhz (radio control band) and the tx output stage as it stands puts out maximum power of 475mW with a 140 ohm resistor as load. I only *need* 50mW ERP., however, so can stand to see quite a bit of loss from an inefficient antenna. The antenna I will be using is a telescopic whip - exactly the same set-up as you see with model vehicle radio control transmitters- which is what it is, in fact. It ain't rocket science. Someone out there must know the radiation resistance of such a telescopic whip (which has a ground plane of just around 16 square inches contained within the remote control handset) and the best way to couple it to a PA with a 140 ohm output impedance? You have had quite a few answers which seem pretty good to me. I have a few comments. Stop saying "radiation resistance" and start saying "input impedance" or "feed impedance." Once you know the input impedance, getting maximum power transfer is a straightforward matching problem that can be solved in a variety of ways. True, you won't know for sure how much power is "getting out," but some of the posts in this thread have given you some estimates. If that isn't good enough, then you will have to measure by putting a receive antenna in the far field. Anyway, if you want to measure the input impedance, you should be able to do it with a two-channel oscilloscope and a 40 MHz function generator. Drive the antenna with the function generator and simultaneously measure the input voltage and current, including the phase relationship between them. The input impedance is V/I. To measure the current, put a suitably sized resistor in series with the antenna and measure the voltage across it. The voltage across the resistor should be small compared to the voltage into the antenna. If it is too small to see, use a bigger resistor until you can see it. Make sure both oscilloscope probes are grounded in the same place. Unless you have a differential probe (in which case, use it to measure the voltage across the current sensing resistor). From what others have already said, it sounds like the input will be extremely capacitive with a small series resistance. Once you know the details, however, it will be easy to tell you how to match this to your amplifier. That's my $0.02. Mac |
#36
![]() |
|||
|
|||
![]()
In article ,
Paul Burridge wrote: It ain't rocket science. Someone out there must know the radiation resistance of such a telescopic whip (which has a ground plane of just around 16 square inches contained within the remote control handset) and the best way to couple it to a PA with a 140 ohm output impedance? Paul, standard CB antennas are loaded whips, for operation at around 30MHz. Available in the CPC catalogue for about £10 to £20, Perhaps you could start off with one of those and modify to suit. Note also that there is a 433MHz licence-free band for short distance (100m) remote control. Pre-built Tx and Rx modules are cheap, and a 433MHz antenna would be a breeze. www.cpc.co.uk or 08701 202530. -- Tony Williams. |
#37
![]() |
|||
|
|||
![]()
In article ,
Paul Burridge wrote: It ain't rocket science. Someone out there must know the radiation resistance of such a telescopic whip (which has a ground plane of just around 16 square inches contained within the remote control handset) and the best way to couple it to a PA with a 140 ohm output impedance? Paul, standard CB antennas are loaded whips, for operation at around 30MHz. Available in the CPC catalogue for about £10 to £20, Perhaps you could start off with one of those and modify to suit. Note also that there is a 433MHz licence-free band for short distance (100m) remote control. Pre-built Tx and Rx modules are cheap, and a 433MHz antenna would be a breeze. www.cpc.co.uk or 08701 202530. -- Tony Williams. |
#38
![]() |
|||
|
|||
![]()
I'm looking forward
to making some outdoor antenna measurements using the new N2PK vector network analyser... but not today brrrr! Gee, Ian, you only will have to go out and do the short-open-50R calibration at the end of the coax. The software can move the reference plane from the VNA out to the antenna feedpoint, and you can do the rest from the comfort of your shack! Yes, I'm on Harold's list for a kit. 73, John - K6QQ, who thought that after retirement he'd never have the use of a VNA again! |
#39
![]() |
|||
|
|||
![]()
I'm looking forward
to making some outdoor antenna measurements using the new N2PK vector network analyser... but not today brrrr! Gee, Ian, you only will have to go out and do the short-open-50R calibration at the end of the coax. The software can move the reference plane from the VNA out to the antenna feedpoint, and you can do the rest from the comfort of your shack! Yes, I'm on Harold's list for a kit. 73, John - K6QQ, who thought that after retirement he'd never have the use of a VNA again! |
#40
![]() |
|||
|
|||
![]()
I read in sci.electronics.design that Ian White, G3SEK
wrote (in ) about 'Measuring radiation resistance', on Mon, 8 Dec 2003: I'm looking forward to making some outdoor antenna measurements using the new N2PK vector network analyser Is N2PK a call-sign? Are there any details of this analyser on the Internet? -- Regards, John Woodgate, OOO - Own Opinions Only. http://www.jmwa.demon.co.uk Interested in professional sound reinforcement and distribution? Then go to http://www.isce.org.uk PLEASE do NOT copy news posts to me by E-MAIL! |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Forum | |||
Radiation Resistance & Efficiency | Antenna | |||
Measuring radiation resistance | Antenna | |||
50 Ohms "Real Resistive" impedance a Misnomer? | Antenna |