In article ,
says...
"John Miles" wrote in message
...
Thanks.

I'll look at those pdf files on ebay.

The uncal light is unfortunately always on, none of the settings affects it.
The controls seem to work, but they don't affect uncal led. I guess I really
need the manual. Probably something in there that could explain it.

That would make me suspect the keyboard controller chip. In the 492, I
ended up replacing it with a BASIC stamp (which I still have in the junk
box somewhere; you're welcome to it if that's the problem).

Does your TIME/DIV knob do anything at all?

-- jm

What puzzles me in that case is why are all of the functions/buttons working?
Yes, even the TIME/DIV works as expected, all positions. Same goes for other
buttons.

When I turn it on it always starts with some strange settings and I need to reset it,
perhaps the EEPROM or RAM has failed over the years. Or I don't know how to
store the settings.

That's odd, all right. With my 492, I had to manually rotate TIME/DIV
back and forth into the AUTO position after power-up to get the
instrument to read it.

I'm not sure what would cause random or non-standard power-up settings
besides a flaky keyboard controller that doesn't respond to the CPU's
first few accesses after power up. The 496 doesn't have the capability
to store its settings in NVRAM like the 494 and later models, so it
shouldn't be a case of corrupted memory. The EPROMs are checksummed, so
if you don't receive any power-up error messages, they are OK.

I suppose one worthwhile test would be to make *sure* that the UNCAL
light is on for no good reason (as opposed to invalid startup settings).
Power it on, rotate TIME/DIV back and forth leaving it in 5
seconds/division (the slowest setting), and manually set the other
controls for 1 MHz RBW and 100 MHz/division sweep with no video
filtering. The UNCAL light should definitely not be on at that point.
If it is, you can disregard it for the time being if everything else
works right.

I'll poke around in my 492 manual and see if anything leaps out at me.

-- jm

------------------------------------------------------
http://www.qsl.net/ke5fx
Note: My E-mail address has been altered to avoid spam
------------------------------------------------------

"John Miles" wrote in message
...

I'm not sure what would cause random or non-standard power-up settings
besides a flaky keyboard controller that doesn't respond to the CPU's
first few accesses after power up. The 496 doesn't have the capability
to store its settings in NVRAM like the 494 and later models, so it
shouldn't be a case of corrupted memory. The EPROMs are checksummed, so
if you don't receive any power-up error messages, they are OK.

I suppose one worthwhile test would be to make *sure* that the UNCAL
light is on for no good reason (as opposed to invalid startup settings).
Power it on, rotate TIME/DIV back and forth leaving it in 5
seconds/division (the slowest setting), and manually set the other
controls for 1 MHz RBW and 100 MHz/division sweep with no video
filtering. The UNCAL light should definitely not be on at that point.
If it is, you can disregard it for the time being if everything else
works right.

I'll poke around in my 492 manual and see if anything leaps out at me.

-- jm

I tried it, it all works fine or at least seems to, but the "Uncal" LED is on.

I'm reluctant to open it and see where this LED leads to check the logic.
If it goes to the microcontroller and the port is fried, it won't help me much
anyway. Besides, everything else works at this point. I hope its not an early
sign of something else going to hell later on.

Thanks for your help so far.

SioL

Thanks!

Siol

"KLØS" wrote in message ...
I've had very good luck getting Tek manuals from Deane Kidd...send him a
note at:



and see if he might have the manuals you're looking for.

Good Luck!

Dino KLØS/4

"John Miles" wrote in message
...
In article , says...
I've had very good luck getting Tek manuals from Deane Kidd...send him a
note at:



and see if he might have the manuals you're looking for.

Good Luck!

Dino KLØS/4

Good point; he came up dry when I asked him about 497P manuals but he
may well have some for the 496. I bought a brand-new set of 494AP
manuals from him a couple of years ago.

He might have a keyboard controller, for that matter.

-- jm

I still think its not broken since everything works. Except if one of the ports controls that led
as well.

SioL