Home |
Search |
Today's Posts |
#21
![]() |
|||
|
|||
![]() Leigh wrote: "citizensband" wrote in : All the garbage about how you should even be allowed to operate a CB, unless you are able to build your own equipment. Real Hams will never be able to build a rig that even comes close to what's available off the shelf these days. .....and a true example of home-built radio was heard on 80m CW a week or so ago - a Russian with homemade equipment that rasped CW more than broke the carrier and was a wide signal. Sort of knocks the 'build your own' case for Gareth into a cocked hat - not easy to work or even work out who or where he was. Leigh..... You were probably hearing a keyed parasitic oscillation. |
#22
![]() |
|||
|
|||
![]() zpk_12wpm wrote:. that and the tone that starts high and goes low as the dah dah dah is sent. That one usually comes from Cuba |
#23
![]() |
|||
|
|||
![]()
ISTR that the programming interface for PLL chips is the three wire serial
form, with a static clock. you _COULD_ drive it with three switches, but you'd have to at least debounce them - RS flip-flop from NAND ususally being the simplest way. Might be interesting to derive a driving circuit from el-bug principles! Scott Dorsey wrote in message ... All of the AD synthesizers I have seen have a microprocessor interface, where they basically memory-map into a processor. I'd rather have something I can directly address. I could probably pull out a 68HC11 to control the thing if I absolutely had to, but I'd rather have something I can just latch a BCD input into. --scott |
#24
![]() |
|||
|
|||
![]()
Jim Hampton wrote:
Sheesh! 1 GHz with a 10 bit binary counter. Only $350.00 each in quantities of 1000. Someone care to loan me over 1/3 of a million? Seriously, however, there are affordable AMD devices but they appear to be in the 50 MHz to under 200 MHz range. I could do that. Generate a 50-80 Mhz sine wave, then put it into a mixer with a 50 Hz crystal oscillator and turn it into a DC-30 Mhz signal. I think I could even get a brickwall high pass at 30 MHz so the whole thing would be broadband with no tuning. Of course, you'd lose some stability in the process from those extra stages, but probably not enough to be a big issue. Oh, and for 10M FM, of course, I could modulate the local oscillator. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#25
![]() |
|||
|
|||
![]()
In article , Dick Carroll wrote:
Leigh wrote: "citizensband" wrote in : All the garbage about how you should even be allowed to operate a CB, unless you are able to build your own equipment. Real Hams will never be able to build a rig that even comes close to what's available off the shelf these days. .....and a true example of home-built radio was heard on 80m CW a week or so ago - a Russian with homemade equipment that rasped CW more than broke the carrier and was a wide signal. Sort of knocks the 'build your own' case for Gareth into a cocked hat - not easy to work or even work out who or where he was. You were probably hearing a keyed parasitic oscillation. Yup. I am sorry to report that my first homebrew rig did the same thing too. Some of the eastern european folks I know are still rockbound, and some of them are cutting their own crystals. This is a recipe for parasitics, or at least it was when I tried doing it in high school. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#26
![]() |
|||
|
|||
![]() |
#27
![]() |
|||
|
|||
![]()
Too many eggs in the diet?
On 17 Jul 2003 10:33:21 (Scott Dorsey) wrote:- Some of the eastern european folks I know are still rockbound, |
#28
![]() |
|||
|
|||
![]() "Airy R Bean" SPAM@trap wrote in message ... Too many eggs in the diet? On 17 Jul 2003 10:33:21 (Scott Dorsey) wrote:- Some of the eastern european folks I know are still rockbound, No, that would be egg bound. -- Jon |
#29
![]() |
|||
|
|||
![]() "citizensband" wrote in message ... All the garbage about how you should even be allowed to operate a CB, unless you are able to build your own equipment. Real Hams will never be able to build a rig that even comes close to what's available off the shelf these days. Most people can't even be bothered, have no interest or don't have the time to build rigs anymore. Boatanchors should be used for exactly that, anchoring boats! Time to stop whinging, and face the facts...Real Technology has overtaken you all! tox In all honesty, unless go in for VERY low power ( 1Watt), the problem is that you are going to have real problems ensuring that you don't generate unacceptable levels of spurious emissions. To properly test things to the standard required nowadays, with today's high density of electronic equipment in any residential area, you will need test equipment costing much more than a brand new 'off the shelf' set. But it is certainly possible to design your own passive circuits, for instance filters and traps, without this risk being involved. If you are interested in DX, then a commercially designed receiver is going to be much more sensitive and selective, of course. This is due to the fact that a multinational company has the development resources that an individual could only dream of. Obviously, you do gain a lot of respect for designing your own circuits, and you will attract a lot of interest by doing so! So I don't think that 'home brew' will ever die out in it's entirety! DN |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Forum | |||
Reflection Delay is it real??? | Antenna | |||
50 Ohms "Real Resistive" impedance a Misnomer? | Antenna | |||
Why don't Real Hams you face the facts? | Policy | |||
Why don't Real Hams you face the facts? | Boatanchors | |||
Why don't you Real Trolls face the facts? | Boatanchors |