Cleaning Out - Many Items for Sale or Trade. All need a new home....
************************************************** *******

Motorola Trunk Units

Mitrek
Mod: T83JJA3900DK
Ser: 433HKJ1366
Xmtr: CC343
RCVR: 8C0216
HUD1072CPR
PA: HLD4042A8PRW
HLN4181APF plug-in board with TRN4224A (156.7)
Unit has lock "converted to screwdriver slot"
Have Motorola Microphone and Control Head that appear to go with this model

$15.00 plus shipping

Micor
XMtr: CC4165
RCVR: RC0003
Mod: T44RTA30038A
Ser: 203CF00527
11 Channel Elements in 460MHz range.
Bottom plate is removed (but available)
lock intact - Bottom may have been pried off
Have Motorola Microphone and Control Head that appear to go with this model

$15.00 plus shipping


************************************************** ************************

AOR 1000XLT Wide Range Monitor Receiver

Handheld Unit
500 MHZ through 1300 MHZ (continuous coverage)
AM / FM / FMW (WideBand)
1000 Channels - 10 banks

$100.00 OBO Plus shipping

************************************************** *******
Yaesu FT-50RD Handheld

Has enhanced keypad and fairly good battery. No charger, paperwork, box or
other accessories.

This HT works, but is a real stress generator. The top rotary encoder
(channel selector, menu advance, memory, advance, etc.) rotates normally,
but will toggle between forward and backwards selections. You can
eventually find the channel, selection, frequency that you want, but it may
go backwards, forwards, not advance... Anything can happen. Other than
that, it is a great talker. The battery takes and holds a charge and looks
to be in good shape.

I am keeping the antenna and charger for another rig. It will come with
radio and battery.

$100.00 OBO Plus shipping

************************************************** ********************

Yaesu VX-5R

HT, Box, Packing, Charger, Manual, Standard antenna(s) and tip(s)

This HT has problems; the antenna is loose at the connector and it has no
measurable output. Additionally, it was opened up to be sure that the
correct screws were used on the belt clip ( a common source of failed
outputs), and the conector that holds the ribbon cable between halves is not
retaining the cable properly. It showed signs of have been opened for
inspection before. It was purchased used with low output, and was being
used with a Yaesu Car DC Adapter (the correct one for this model) when it
overheated and lost all measurable output. It will do great as an
extremely near field test device; I use it for talking into a 6m repeater I
have been setting up. I can get about 300' range from the repeater antenna,
under the best conditions. It may be worth sending back to Yaesu for
repair, or for parts to combine with another broken unit. It has the baro,
altitude and temp sensors installed in it.

$75.00 Plus shipping

************************************************** ******



Kenwood Sirius Satellite Radio

Kenwood Tuner (KTC-SR901), Display unit with RF Modulator (KCA-RF701M) and
Terk antenna (TRK-SR20S) - With all original packaging, documents, etc. -
Removed from car when traded in. - Antenna will need a re-mount kit. -
Bought New around 2003, and traded in car later for one that had Sirius
already installed.

$45.00 OBO Plus shipping

************************************************** **********

Standard Horizon 6 Series Marine HT

No Battery
Comes with Antenna and Destop Charger
Has Crysytals for Channels 6 and 16
Fairly Clean

$10.00 plus shipping

************************************************** **************

Motorola Radius p50+ HT

Has DTMF Pad, Standard Charger - HTN9046B with Wall Wart
Currently on 151.685 MHz Simplex - No PL - Belt Clip mount is broken on
rear.
Radio squeals when first turned on, but seems to operate normally after
that.
Battery holds some charge, but will need replacing.

$35.00 Plus Shipping

************************************************** ***********************

Optoelectronics Scout 40

- Needs repair -
Rapid charge not working properly, but charges on slow charge OK. Battery
still holding good charge. Sensitivity is way down as a result of exposure
to a stronger RF Field than the front end was designed for. Unit still
comes on, display and switches all work, just very low sensitivity. (IF I
Recall Correctly, a 1v signal above 450 MHz would register). Overall, in
good condition. - These sold for $350.00 to $400.00 new -

$50.00 Plus shipping

************************************************** *****************

Icom IC-R2 Receiver in very good Condition.

This is the Export Model and is the same as the R2-07-GOVT model

$100.00 plus shipping

************************************************** *****

Skutch T-51A / 3 - Line Swinger (Telecomm)

This is an intersting device that is used to route 3 lines to one device
(phone, answering machine, modem, etc). It will automatically pick up the
first line that rings and send a busy signal to the remaining two. Useful
in a small business during lunch hours or similar situations. Very unique.
In As-New condition.

$10.00 plus shipping

***********************************************

Curtis Electro Devices Model ESNR-5900


Analyzer, Antenna, Charger and Manual for a similar model. Used in Cellular
sales to ID phone information prior to programming a used phone. Will read
ESN ONLY after initiating sequence on phone in near field. Will not snarf
pairs for illegal use. This is a basic, low-power cell-site. It emulates
Cell-Site operation within the AMPS service to initiate communications with
a cellphone within a very short distance in order to extract info necessary
to reprogram/reactivate that phone.

It will not read any phone information unless the phone is close by, and
only after that phone has dialed an non-compatible number sequence, that
will not result in an completed call.

This is not an illegal monitoring device; it was marketed as a sales-support
tool for cellular dealers - Cira 2nd Quarter 1995.

This unit was assembled from end-run parts inventory when the line was
discontinued, so the manual isn't the correct on for this model (but
explains overall use) and the charger may not be the correct MAh rating for
the batteries installed. It uses 10 AA NiCad batteries and willl need
replacements. It will be shipped without batteries to save weight (the ones
in it were starting to show signs of seepage).

This is in a case that is 9"H x 6"W x 2"D and weighing 2 pounds.
Original retail to cellular sales outlets was $1295.00

Make offer or trade via email if interested.

************************************************** ***
RSA Security Smart Card Reader - Part Number: 903396 Revision 1.0

This is a Bulk Packaged unit. No software, instructions or additional items
included. Unit has self adhesive pads for semi-permanent installation, as
well as fold down front leg and rear rubber "anti-skid" pad for placement on
any flat surface. Cables include a Serial (DB-9 female) connector that goes
to the unit and also has a second cable coming from the DB-9 that goes to
both Male and Female PS-2 type Keyboard connectors (6 pin mini-din) for
feed-through connection to keyboard cable.

I believe the setup is to allow data through the Serial connection and to
pick up power for the card reader circuit through the Keyboard connection.

The bottom label shows power demands of 5 VDC at 100 mA.

Inside the unit, the top of the board is marked:
SCR111 104080
Rev 1.0 JAN 00
SCM Microsystems

Above the "Card Cage " is silkscreened: S-CARD

The actual "card cage" has the markings JAE and T269

Removing the top of the card cage shows 8 contacts in 2 rows of 4, as well
as a single contact separate from the
8 (possibly a CE pin??)

The bottom of the board inside has
PIC 1626C622A-20/SO (U3)
14 pin SM DIP 2C16 / HC74 (U2)
16 pin SM DIP ADM2052EARN / 0221 / K21517 (U1)
14.28 (X1) Appears to be 14.28 MHz timebase crystal

There is a 8 pin header marked J3 that is attached to both top and bottom
boards (4 pins on each) as well as solder points (W1 - labeled 1 through 5)
for additional connections. Thease appear to be plated through holes
connecting both the top and bottom of the PCB. These lines appear to go
from PIC to card cage and power source.

I don't know enough about this to determine if it is can be easily set up as
a programmer also.

I have a bunch of these, bulk packaged in anti-static bubble wrap. New,
never used.

$6.00 each plus shipping

*********************************************

AIM Products Model 15-5010 Push Button Coaxial Switch.

Use for selecting 2 sources for one Television, VCR, etc. - "F"
Connectors for inputs and outputs on rear
A and B Switches on front - Can be mounted with supplied screws or
supplied double-sided tape. - Units for bid are in original sealed plastic
bags. New Old Stock, never used.

Great for selecting 2 antennas to one receiver or feeding 2 receivers from
one antenna. Plus, up can always use them to switch between cable and a
VCR.

$2.50 each plus shiping (Have 6 available)

************************************************** ***************



All items are U-Ship from 31523 - Brunswick, GA.

I charge actual shipping cost, and will ship via USPS Priority on lighter
items or FedEx Ground/Home Delivery on heavier ones. I will combine
shipping on multiple items. I want to get rid of this stuff far more than I
want to make a buck or 2 on shipping.

I will accept trade offers on Ham gear, Receiving gear, other electronic
items.

I am looking for an Icom IC-T90A HT, Midland Syntech I Low-Band LMR Rigs
(70-052, 050, 056 C models), Midland Syntech II accessories, Midland LMR
Microphones......

Contact me off the NG @ or or address
in the header (if shown)

David
KD4NUE